EXACTLY HOW TO INSTALL A BATH TUB YOURSELF

Exactly How to Install a Bath Tub Yourself

Exactly How to Install a Bath Tub Yourself

Blog Article

Contact Us

On this page down the page you can get more sound advice with regards to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


Tools You Need to Install a New Bathtub
Installing a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a new one is also a moderately tough task. If the old tub is readily easily accessible, the task can relocate speedily; if you have to open a wall to eliminate the old bathtub and also place the new bathtub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will need a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually certified on your own for the job and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is far better to take into consideration using one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new tub in your restroom if you have already bought a new tub and do not require to transform the setup of your previous water pipelines.
Your devices as well as material checklist ought to consist of the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Blade

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipe Caps


  • Preparing for the Installation


    To start with, the sustaining structure provided with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to prevent stress on the bathtub.
    Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. Make certain you use every one of the supplied washers.
    Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final placement.

    Removing Old Taps


    If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite troublesome due to the limited accessibility that is typically the instance.
    Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
    Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.

    Mounting the Bathtub


    Using the two wood boards under its feet, position the bathtub in the required setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four little factors.
    The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub till the level reviews level.
    To install taps, fit the bottom of the outermost adaptable faucet adapter to the ideal supply pipe by making a compression join; then do the same for the other tap.
    Switch on the supply of water as well as check all joints as well as new pipework for leakages as well as tighten them if needed. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
    Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling as well as securing around the tub must wait up until the tub has been used at least once as this will resolve it right into its last setting.

    Fitting New Taps


    If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a connection to the current supply pipelines.
    If you require to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
    Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washing machines remain in location between the faucet and also the sink. Protect the tap in position with the producer provided backnut. As soon as the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The former kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bath tub


    In the area where the bathroom satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to issues with dampness as well as possible leakages to the ceiling listed below.
    You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched paper or soft rope. Remember to always load the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can crack relatively very early if you do not take into consideration this movement before securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub Yourself

    Do you appreciate reading up on Tools You Need to Install a New Bathtub ? Place a review down below. We will be interested to see your reactions about this blog posting. We are looking forward that you come back again before long. Feel free to take the time to distribute this page if you liked it. We take joy in reading our article about Tools You Need to Install a New Bathtub .




    View Website


    Report this page